![]() Tip: If it is not possible to configure a DNS server accordingly, or to ensure the transmission of multicasts between phone and SwyxServer, you can create the string REG_SZ LocalIpAddress in the registry under HKLM\Software\Wow6432Node\Swyx\General\CurrentVersion\Options on the SwyxServer and enter the IP address of the SwyxServer there, as well as restart the SwyxServer service afterwards. (!) It is important that the DNS server in the network is configured correctly and can resolve the DNS name of the SwyxServer communicated in the URL (in the example ). The phone will call this provisioning URL. This NOTIFY message contains a provisioning URL for the phone in its content. The SwyxServer will answer this multicast message with a SIP 200 OK and send a SIP NOTIFY to the phone. The Yealink phone sends a multicast to the network (SIP SUBSCRIBE) during commissioning. In this case, however, no communication with the Yealink provisioning server is necessary. Provisioning for SwyxWare on premisesĪlso in the on premises case the phone including its MAC address is created in the SCC. the IP address of the responsible SwyxServer. As soon as the Yealink phone is connected to the network and starts for the first time, it will contact the Yealink Provisioning Server and receive the initial configuration data, e.g. In addition to the MAC address of the phone, the IP address of the SwyxServer assigned to this phone is also stored. Provisioning for SwyxONĪfter the phone including its MAC address has been created in the SCC, SwyxWare stores the MAC address of the phone at the Yealink provisioning server. Please refer to the Swyx Control Center online help for the individual steps. In both cases the phone must be created in SwyxWare using the new Swyx Control Center (SCC), the web-based administration of SwyxWare, and assigned to a SwyxWare user via its MAC address. Provisioning the phonesįor the provisioning of telephones, a distinction must be made between operation with the SwyxON cloud solution and SwyxWare on premises. Then open the SCC in the browser of your choice via During the SwyxWare installation you were asked to create an administrative account. The SCC is based on the IIS, which can be installed if necessary. You install the SCC separately via the SwyxControlCenter.msi installation package on the SwyxServer. In the SwyxWare on premises case proceed as follows: The configuration is not possible via the previous MMC based SwyxWare Administration.įor SwyxON all necessary installations regarding SCC are done automatically for you. The Swyx Control Center (SCC) is mandatory for the installation and configuration of the new DCF/Yealink phones. Where possible, the DCF is based on the RFC standards and defines clear interfaces for the areas that are not specified in the RFCs.ĭCF is not limited to the usual call scenarios, but also covers the CTI / remote control functions for SIP phones according to uaCSTA specification. It ranges from -300 to 300, the default value is 60.With the Device Connection Framework (DCF), Swyx defines a standard that enables every telephone manufacturer to integrate their SIP phones into SwyxWare. The value format is the same to the start time. #For example, the value 1/4/2/5 means the start time is at 5 o'clock on Tuesday of the 4th week in January. #If the DST type is configured as By Week, the value format is Month/Day of Week/Day of Week Last in Month/Hour of Day. For example, the value 5/20/10 means the start time is at 10:00 on May 20. #If the DST type is configured as By Date, the value format is Month/Day/Hour. #Configure the DST type when the DST feature is enabled 0-By Date (default), 1-By Week #Configure the daylight saving time feature 0-Disabled, 1-Enabled, 2-Automatic (default) #Configure the update interval (in seconds) when using the NTP server. #Configure the domain name or the IP address of the NTP server. Currently this is only available via the GUI. I am looking for the configuration file that will allow me to choose a time zone so the phone will display the correct time. Using T46G behind Broadsoft firmware version 28.71.193.8.
0 Comments
Leave a Reply. |